Search

Page 1 of 86 (852 items) 1 2 3 4 5 Next > ... Last »
  • Re: Noisy drivetrain

    [quote user="bobbob"]. Drivetain was noisy with worn cassette and is now noisy with brand new too. [/quote] If noise is still there after you have changed cassette and chain (and assuming you have properly adjusted cable tension and set limit screws), then unaligned hanger is MOST likely culprit...
    Posted to Forum (Forum) by eddymerckx3 on 08-01-2017
  • Re: Noisy drivetrain

    in addition to suggestions from @Rob1519.... check your rear der hanger alignment with proper tool.
    Posted to Forum (Forum) by eddymerckx3 on 07-30-2017
  • Re: S3 Derailleur Hangar, and seat stay bends when quick release is fastened

    ...slight movement of the dropout (and attached hanger) is normal when locking your quick release. The movement will be more obvious/pronounced if your hanger is loose. As others have said, start by making sure the two small screws that hold your dropout are firmly fixed, but do not over tighten. Buy a Park Tools DAG 2 hanger alignment tool ...
    Posted to Forum (Forum) by eddymerckx3 on 07-30-2017
  • Re: Stack and reach numbers on frame sticker do not match what is on website

    ...that is the case with may Cervelo models. Use the #s on website.
    Posted to Forum (Forum) by eddymerckx3 on 06-11-2017
  • Re: Enough Clearance Crankarm/FD Cage?

    ...might be the angle of the pic, but it appears as if your outer cage is 5-6 mm too far outboard. With the outer cage parallel to your large chainring and your chain in the big ring, there should be a 0.5-1.0mm gap between the outer edge of your chain and the inner side of the outer cage plate.
    Posted to Forum (Forum) by eddymerckx3 on 04-24-2017
  • Re: New R5

    ...this could be interesting. I see internal seat post clamp and hero shaped seat post; beefier but still aero shaped downtime; what appears to be a very square top tube; no more pencil seat stays and what appears to be beefier rear dropouts;much larger fork;taller chain stays? What else?
    Posted to Forum (Forum) by eddymerckx3 on 01-31-2017
  • Re: Is this normal?

    ...slight movement of the dropout (and attached hanger) is normal when locking your quick release. The movement will be more obvious/pronounced if your hanger is loose. As others have said, start by making sure the 2 small screws that hold your dropout are firmly fixed, but do not over tighten (while u r down there u might as well remove the ...
    Posted to Forum (Forum) by eddymerckx3 on 12-03-2016
  • Re: Looking for advice on old RS frames

    Stay away...I had 3 pre-2011 R-series frames replaced all with infamous BB crack, definitely not an issue worth gambling on without a full warranty, unless u r getting frame for free. BTW, I have also had 2 post 2011 frames replaced as well (YES, 5 total in 6 years). The BBRIght frames were not BB failures. Despite the numerous issues I still love ...
    Posted to Forum (Forum) by eddymerckx3 on 10-19-2016
  • Re: Presta valve thread

    RESPECTFULLY, challenging a response from a fellow forumite regarding an inquiry that is more obvious then soup, is sort of uncool, especially when the answer to your question (as already pointed out above) is a simple google search away. Simply google presta valve, thread pitch and you will find about one-gazillion sources that provide you the ...
    Posted to Forum (Forum) by eddymerckx3 on 10-10-2016
  • Re: R3 creaking.

    [quote user="Goleafsgo5"] Update"   We changed the crank thinks don't to date   2 pairs or shoes New BB Checked Cassette lock ring spec'd all bolts changed crank.  diff pedals the shop is tossing in the towel its going back to Cervelo.   :( [/quote] I don't see ...
    Posted to Forum (Forum) by eddymerckx3 on 09-17-2016
Page 1 of 86 (852 items) 1 2 3 4 5 Next > ... Last »
Copyright © 2007-2013 Cervélo Cycles Inc. All rights reserved.